Digital Monitoring Products XT50 Guide d'installation télécharger pdf (Page 26)

XT Series Programming Guide Digital Monitoring Products

SYSTEM OPTIONS

9.7 Cross Zone Time

Enter the time allowed between zone faults. When a zone programmed for cross zoning

faults, the panel begins counting down the Cross-Zone Time entered here. If the same

zone or another cross-zoned zone faults within this time, an alarm report is sent to the

receiver.

If the Cross-Zone Time expires without the second zone fault, only a zone fault report

from the rst zone is sent to the receiver. The Cross-Zone Time can be from 4 to 250

seconds in one second increments. Enter 0 (zero) to disable the Cross-Zone Time

feature. See the Appendix.

9.8 Power Fail Delay

This option tracks the duration of an AC power failure. The delay time can be from 1

to 9 hours. When the AC power is off for the length of the programmed delay time, an

AC power failure report is sent to the receiver. For example, if the power failure delay

is set for two hours, then the AC power failure report will be sent between 2-3 hours.

Entering a 0 (zero) sends the AC power failure report within 15 seconds.

9.9 Swinger Bypass Trips

Enter the number of times (1-6) a zone can go into an alarm or trouble condition within

one hour be fore being auto matically bypassed. Bypassed zones are auto matically reset

when the area they are assigned to is disarmed. All 24-hour zones are reset when any

area of the system is dis armed. A programming Stop operation restores a bypassed zone.

Entering 0 (zero) disables this function. Default is 2.

How it works

The panel hour timer starts at 59 minutes past the hour. If the hour timer expires before

the trip counter is exceeded, the trip counter returns to 0 (zero). If the trip counter is

exceeded before the hour expires, the zone is auto matically bypassed by the panel. A

Bypass Re port is sent to the receiver if Bypass Re ports is YES.

9.10 Reset Swinger Bypass

When YES is selected, an auto matically bypassed zone is reset if it remains in a normal

condition for one complete hour after being bypassed. A report of the automatic reset is

sent to the receiver if Bypass Reports has been se lected as YES. Default is NO.

9.11 Telephone Access

YES allows the use of standard DTMF telephones to arm and disarm and check the armed

status of the XT30/XT50 panel. Refer to the XT30 or XT50 User’s Guide for complete

information.

9.12 Zone Activity Hours

This option provides supervision of a person living alone for non-activity. Enter the

number of hours, 0 to 9, allowed to elapse without a disarmed zone being tripped before

a message is sent to the receiver. Default is 0 (zero).

When the system is disarmed, the timer begins to countdown the number of hours

programmed. Each time activity occurs, the timer restarts the countdown.

Before the countdown time expires, the keypad sounds a tone and PRESS ANY KEY

displays to allow the user to restart the activity timer. The duration of the tone is the

number of seconds programmed for Entry Delay 2.

Select the SUPV/TRBL receiver option in communication programming to send S93

ALARM: User Activity Not Detected, S94 Alert: Activity Check Enabled, and S95 Alert:

Activity Check Disabled messages.

When an open/close schedule is programmed, the timer only counts down during the

scheduled open period. Also, when a schedule is programmed, if the timer is counting

down and the scheduled open time occurs, the timer resets and begins the countdown

again.

CRS ZONE TM: 0

PWR FAIL HRS: 1

SWGRBYPS TRIPS: 2

RST SBYP NO YES

PHONE ACC NO YES

ZN ACTY HRS: 0

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 54 55

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XT50 Guide d'installation Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XT50