Digital Monitoring Products XT50 Guide d'installation télécharger pdf (Page 47)

Digital Monitoring Products XT Series Programming Guide

APPENDIX

Activate Cell (263C Only)

Note: (Version 122 or higher rmware) If the 263C Cellular Communicator has not been previously

activated, Automatic Cellular Activation is performed when the panel powers up or is reset.

ACTIVATE CELL is only necessary when Automatic Cellular Activation is not successful and

communication was not established.

To begin the cellular activation for a 263C CDMA Cellular Communicator, verify that the 263C MEID has

been added for the panel using Remote Link or by calling Customer Service (1-800-641-4282). At the

keypad, press any top row Select key when ACTIVATE CELL is displayed on the keypad. When the

SURE NO YES? conrmation menu appears press the Select key beneath YES to complete the cellular

activation.

Successful Display Failure Display

CELL ACTIVATED NOT ACTIVATED

Email Status

The Email Status menu tests each component of the panel’s e-mail communication. The test proceeds

until the rst component failure or until all components have been tested with positive results. The test

screen displays after each component for two seconds or until the CMD key has been pressed.

Panel Settings

Hitting a top row key allows access to the MAC Address, Serial Number, Model, and Firmware Version.

MAC Address

Short for Media Access Control address. This hardware address uniquely identies each network node. Not

to be confused with an IP address, which is assignable. The MAC address is the panel on-board network

hardware address. Press any top row Select key to display the panel MAC address.

Serial Number

This number is the network communicator serial number. Reference this number for communicator date-

of-manufacture, hardware version, etc. Press any top row Select key to display the Serial Number.

Panel Number

This menu option displays the model number of the panel. The display will show XT30 or XT50 followed by

1-3 letters to indicate the communication type: C=Cellular, D=Dialer, N=Network.

Firmware Version

This menu option displays the Firmware Version number of the panel and date it was released.

Z-Wave Test Option

This feature allows the installer to test panel communication with Z-Wave devices.

A successful test indicates a response from a device. Press any top row Select key

to view the Z-Wave Device List.

Press COMMAND to advance through each Z-Wave device and press any top row

Select key to begin the test on the device displayed.

The name of the device displays above the device number. The current number of

successful communications followed by the total number of attempts displays to

the right of the device number. The test stops after 99 attempts.

Press COMMAND to view the nal number of successful communications.

Exiting the Diagnostics program

Press the COMMAND key until STOP displays. Press any Select key. The keypad returns to the Status List

display.

17.4 Using the 984 Command Function

This feature allows you to connect to a service receiver, primarily used to bring a new account on-line as

it allows you to upload panel programming completed in Remote Link™. There are four options to allow

manual seizure: Number, Pickup, Network, and Cell.

Note: When not in the Programming Menu, the function 984 + COMMAND can be entered at the keypad,

and a remote options menu appears. This menu contains the following options:

NBR

After completing panel programming in Remote Link, set a trap to seize the panel when it calls. Traps are

set by selecting Panel > Trap. Refer to the Remote Link User’s Guide, LT-0565, or Remote Link’s Help File

for complete information about setting traps.

TEST ZWAVE

DEVICE LIST:

HALLWAY LIGHT

LIGHT 02 0/0

HALLWAY LIGHT

99/99 SUCCESSFUL

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 53 54 55

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XT50 Guide d'installation Page 47

Commentaires sur ces manuels

Grundig GMN2200 manuels

Grundig GMN2200 Fiche technique (1 pages)

Table des matières

Plus de produits et de manuels pour Moulins à café Grundig

Digital Monitoring Products XT50 Guide d'installation Page 47

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XT50

Grundig GMN2200 manuels

Grundig GMN2200 Fiche technique (1 pages)

Table des matières

Plus de produits et de manuels pour Moulins à café Grundig