Digital Monitoring Products XTL Series Guide d'installation télécharger pdf (Page 14)

XTL/XTLC Programming Guide Digital Monitoring Products

COMMUNICATION

3.10 Second GPRS APN (XTL Only)

Enter the second APN (Access Point Name). This works as a backup in case the rst APN

fails. The APN may contain two lines of 16 characters to equal 32 character Default is

set to SECURECOM400.

3.11 Receiver 1 Programming

Allows you to set the options for the rst receiver the panel attempts to contact when

sending reports. The XTL/XTLC supports communication to two receivers.

3.12 Alarm Reports

YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and

System Recently Armed reports to be sent to this receiver. Default is YES.

3.13 Supervisory/Trouble Reports

YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and

Fault reports to be sent to this receiver. Default is YES.

3.14 Opening/Closing and User Reports

YES enables Opening/Closing, Code Changes, and Bypass reports by user to be sent to

this receiver. Default is NO.

3.15 Test Report

Enter YES to enable the Recall Test report to be sent to this receiver.

3.16 First IP Address

Enter the rst (primary) IP address where the panel sends cell messages. Enter all

12 digits and leave out the periods. For example, enter IP address 192.168.0.250 as

192168000250. The periods display automatically.

The message is sent using rst GPRS APN and the rst IP Address. If no acknowledgment

is received, rst GPRS APN and the second IP address are used, followed, if needed, by

second GPRS APN and rst and second IP addresses, respectively.

3.17 First IP Port

Enter the rst IP port number to be used in conjunction with the rst IP Address. The

IP port identies the port used to communicate messages to and from the panel.

The default IP Port setting is 2001.

3.18 Second IP Address

Enter the second IP address where the panel sends network messages. Enter all 12

digits and leave out the periods. For example, enter IP address 192.168.0.250 as

192168000250. The periods display automatically.

3.19 Second IP Port

Enter the second IP port number to be used in conjunction with the second IP address.

The IP port identies the port used to communicate messages to and from the panel.

The default IP Port setting is 2001.

3.20 Receiver 2 Programming

Allows you to set the options for the second receiver the panel attempts to contact

when sending reports. The XTL/XTLC supports communication to two receivers. If you

select YES for any of the Receiver 2 options, you must have at least one IP address

programmed in Receiver 2 programming. Receiver 2 defaults are set to NO.

3.21 Alarm Reports

YES enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and

System Recently Armed reports to be sent to this receiver. Default is NO.

3.22 Supervisory/Trouble Reports

YES enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and

Fault reports to be sent to this receiver. Default is NO.

3.23 Opening/Closing and User Reports

YES enables Opening/Closing, Code Changes, and Bypass reports by user to be sent to

this receiver. Default is NO.

SECURECOM400

SECOND GPRS APN

RECEIVER 1 PROG

ALARM NO YES

SPV/TRBL NO YES

O/C USER NO YES

TEST RPT NO YES

FIRST IP ADDR

000.000.000.000

FIRST IP PORT

2001

SECOND IP ADDR

000.000.000.000

SECOND IP PORT

2001

RECEIVER 2 PROG

ALARM NO YES

SPV/TRBL NO YES

O/C USER NO YES

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 48 49

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XTL Series Guide d'installation Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XTL Series