Digital Monitoring Products XTL Series Guide d'installation télécharger pdf

InstallatIon GuIde

9000 Series Wireless Keypads

Description

The DMP 9060 and 9063 are fully functioning supervised wireless keypads. They provide installation exibility while also

offering optional codeless arming and disarming capabilities. Each keypad provides:

• Custom 32-character full LCD display

• Three 2-button Panic keys

• Backlit keyboard with easy-to-read lettering

• Internal speaker

• Wall tamper protection

• Keyboard backlighting turns Red in alarm conditions

The Model 9063 keypad also provides a built-in proximity card

reader designed to read DMP/HID proximity credentials for

codeless arming and disarming.

Compatibility

All DMP 1100 Series Wireless Receivers and Panels

What is Included

The 9000 Series Keypad includes the following items:

• One wireless keypad mounted in a Thinline two-part

housing (base and cover)

• One internal rechargeable 3.7V lithium battery

• One 12 VDC DC Plug-in Power Supply

• Serial number label

• Model 9063 also includes a built-in proximity card reader

Keypad Serial Number

For your convenience, an additional pre-printed serial number label is included. Prior to installing the device, record the

serial number or place the pre-printed serial number label on the panel programming sheet. This number is required during

programming.

Programming the Transmitter in the Panel

The keypads can be programmed into the control panel by entering the serial number in Device Setup panel programming,

or alternatively using the wireless keypad association operation (see below). A maximum of 4 keypads may be used with

the panel.

Device Setup Programming

Program the keypad as a device in Device Setup during panel programming. At the serial number prompt, enter the eight-

digit serial number. Continue to program the device as directed in the panel programming guide.

Note: If the keypad serial number is entered manually, the Wireless Keypad Association operation is not required.

Wireless Keypad Association

Enable Wireless Keypad Association operation on both the keypad and panel.

To enable association operation in the keypad, access the Installer Options Menu (3577 (INST)) and select RF Survey. The

keypad logo LEDs turn on Red until association is successful.

To enable association operation in the XTL panel, press the XTL RESET button 3 times within 12 seconds allowing 3 seconds

between each press of the reset button. When in keypad association, the XTL Red and

Green logo LEDs turn on steady.

To enable association operation in the XR100/XR500, XR150/XR350/XR550 or XT30/XT50

panel, reset the panel 3 times within 12 seconds. Allow the keypad bus Transmit/Receive

LEDs to turn back on between each reset.

For 60 seconds the panel listens for wireless keypads that are in the Installer Options

Menu (3577 CMD) and have not been programmed, or associated into another panel.

Those keypads are assigned to the rst open device position automatically based upon

the order in which they are detected. The keypad logo turns Green to indicate it has

been associated with the panel.

Selecting the Proper Location

The 9000 Series keypads provide a built-in survey capability in the Installer Options menu to allow one person to conrm

keypad communication with the panel. See Accessing Keypad Wireless Survey later in this document.

32-Character Display

Data Entry Digit keys

COMMAND Key

Back Arrow Key

Select Keys

Backlit Logo

and Proximity

Antenna

Figure 1: 9000 Series Keypad

Programming

XMIT

RCV

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 9000 Series Wireless Keypads

InstallatIon GuIde9000 Series Wireless KeypadsDescriptionThe DMP 9060 and 9063 are fully functioning supervised wireless keypads. They provide install

Page 2 - Standby Battery

Digital Monitoring Products 9000 Series Installation Guide2Installing the KeypadAll DMP keypad housings are designed to easily install on any desk st

Page 3 - Backlighting

9000 Series Installation Guide Digital Monitoring Products3Battery Replacement1. Disconnect the battery lead connector from the keypad J3 battery he

Page 4 - End-User Options

Digital Monitoring Products 9000 Series Installation Guide4Backlit LogoThe backlit logo indicates the armed status of the panel and the power and bat

Page 5 - Installer Options Menu

9000 Series Installation Guide Digital Monitoring Products5Installer Options MenuAll keypads provide Keypad Option and Keypad Diagnostic menus to all

Page 6

Digital Monitoring Products 9000 Series Installation Guide6Site cOde POSitiOn: 1 Site Code PositionEnter the site code start position in the dat

Page 7 - Keypad Entry Delay

9000 Series Installation Guide Digital Monitoring Products7Additional ProgrammingThe 9063 keypads allow users to present a proximity credential to th

Page 8 - 800-641-4282

Plus de documents pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XTL Series

Voir le document Digital Monitoring Products XTL Series Guide d'installation

Digital Monitoring Products XTL Series Guide d'installation (16 pages)

Digital Monitoring Products XTL Series Guide d'installation (49 pages)

Voir le document Digital Monitoring Products XTL Series Manuel d'utilisateur

Digital Monitoring Products XTL Series Manuel d'utilisateur (2 pages)

Digital Monitoring Products XTL Series Manuel d'utilisateur (18 pages)

Digital Monitoring Products XTL Series Manuel d'utilisateur (4 pages)

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XTL Series Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XTL Series. Digital Monitoring Products XTL Series Installation guide [en] [fr] Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XTL Series

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XTL Series