Digital Monitoring Products Canadian XR100 Guide d'installation télécharger pdf (Page 22)

Digital Monitoring Products XR100 Series Canadian Installation Guide

InstallatIon

Dry Contact Relay Outputs

12.1 Description

The XR100 Series panel provides two programmable auxiliary SPDT relays when equipped with two DMP Model 305 relays in

socketsK6(Output1)andK7(Output2)andaModel431OutputHarnessontheJ24-pinHeader.Eachrelayprovidesone

SPDT set of contacts that can be operated by any of the functions listed below:

1) Activation by zone condition: Steady, Pulsing, Momentary, and Follow

2)Activationby24-hour7-dayschedule:Oneonandoneofftimeadayforeachrelay

3) Manual activation from the DMP LCD keypad menu

4)Communicationfailure 8)ExitandEntrytimers

5) Armed area annunciation 9) System Ready

6) Fire Alarm or Fire Trouble or Supervisory 10) Late to Close

7) Ambush Alarm

RefertotheXR100SeriesCanadianProgrammingGuide(LT-0896CAN)forspecicinformation.

12.2 Contact Rating

The Model 305 relay contacts are rated for 1 Amp at 30 Vdc (allows .35 power factor). Connect auxiliary power to the

Relay Output 1 common terminal by installing the gray harness wire to terminal 7. Current draw for all connected devices

must not exceed the panel maximum current rating.

12.3 Model 431 Output Harness Wiring

TherelaycontactsareaccessiblebyinstallingtheDMP431OutputHarnessonthe4-pinheaderlabeledJ2.Output2

uses the top three prongs, and Output 1 uses the bottom three prongs. The wire harness and contact locations are shown

below:

Contact Color

Output 1 normally closed Violet

Output 1 common Gray

Output 1 normally open Orange

Output 2 normally closed Violet with white stripe

Output 2 common Whitewithgraystripe

Output 2 normally open Orange with white stripe

The relay contacts must be connected to devices located within the same room as the XR100 Series panel.

Annunciator Outputs

13.1 Description

The four programmable annunciator outputs can be programmed to indicate the activity of the panel zones or conditions

occurring on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground a voltage from

another source. The outputs can respond to any of the conditions listed in the Description section for Dry Contact Relays.

Maximum voltage is 30 Vdc @ 50mA.

13.2 Model 300 Harness Wiring

AccesstheopencollectoroutputsbyinstallingDMP300Harnessonthe4-pinheaderlabeledJ11.Theoutputlocationsare

shown below. For UL applications, devices connected to the outputs must be located within the same room as the panel.

Output Color Wire Output Color Wire

3 Red 1 5 Green 3

4 Yellow 2 6 Black 4

13.3 Model 860 Relay Module

Connect a Model 860 Relay Module to the J11 on the XR100 Series Canadian panel to provide relays for outputs 3-6. Use

these relays for electrical isolation between the alarm panel and other systems or for switching voltage to control various

functions. Power is supplied to the relay coils from a single wire connected to the panel auxiliary power terminal 7. The

module includes one relay and provides three additional sockets for expansion of up to four relays. Mount the 860 inside

thepanelenclosureusingthe3-holepatternandplasticstandoffs.Refertothe860ModuleInstallSheet(LT-0484)as

needed.

Relay Contact Rating: 1 Amp at 30 Vdc (allows .35 power factor)

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products Canadian XR100 Guide d'installation Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products Canadian XR100