Digital Monitoring Products XR20 Guide d'installation télécharger pdf (Page 19)

XRSuper6/XR20/XR40 Programming Guide

2500 N. Partnership Boulevard Springfield, MO 65803 www.dmpnet.com Digital Monitoring Products

6.1 SYSTEM OPTIONS

This section allows you to select system wide parameters used in the operation of

the XRSuper6/XR20/XR40 system. A description of each System Option follows:

6.2 MODE

This configures the panel as either a four Area system (XR20/XR40 only), an All/

Perimeter system (Perimeter/Interior), or a Home/Away system (Perimeter, Interior,

and Bedrooms). Zones must be assigned to Bedrooms for the area to be active.

6.3 CLOSING CODE

When YES is selected, a code number is required for system arming. If NO is

selected, a code number is not required for system arming.

6.4 CLOSING CHECK (XR20/XR40 Only)

Select YES to enable the panel to verify that all areas have been armed after a

schedule expires. If the Closing Check finds any areas disarmed past the scheduled

time, all keypads emit a steady beep and display CLOSING TIME!.

6.5 ENTRY DELAY 1

Enter the entry delay time for all exit type zones programmed to use Entry Delay 1.

When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding

and ENTER CODE:- displays on all keypads.

The area must be disarmed before the delay expires or an alarm report is sent to the

receiver. All Burglary type zones in all areas are delayed along with the exit type

zone. Entry delay times can be from 1 to 250 seconds. Repeat the above for Entry

Delay 2 if it is being used.

6.6 EXIT DELAY

Enter the Exit Delay time for all Exit type zones. When the system is armed, this

Exit Delay time starts and all activity on Exit and Burglary zones is ignored until the

exit delay expires. The delay countdown shows on the keypad for the user. If an

exit zone is in a bad condition at the end of the exit delay:

• the alarm bell sounds for 2 seconds

• an Exit Error report is sent to the alarm receiver

• the bad exit zone is force armed

If any other zone is in a bad condition at the end of the Exit Delay, an alarm on that

zone is indicated. The Exit Delay time can be from 1 to 250 seconds. Enter zero to

disable the Exit Delay feature.

6.7 CROSS ZONE TIME

Enter the time allowed between zone faults. When a zone programmed for cross

zoning faults, the panel begins counting down the Cross Zone Time you enter here.

If the same zone or another zone faults within this time, an alarm report is sent to

the receiver.

If the Cross Zone Time expires without the second zone fault, only a zone fault

report from the first zone is sent to the receiver. The Cross Zone Time can be from

4 to 250 seconds in one second increments. Enter zero to disable the Cross Zone

Time feature.

6.8 POWER FAIL DELAY

This option tracks the duration of an AC power failure. When the AC power is off for

the length of the programmed delay time, an AC power failure report is sent to the

receiver. The delay time can be from 1 to 9 hours. Entering a zero sends the AC

power failure report within 15 seconds.

SYSTEM OPTIONS

EXIT DELAY: 45

ENTRY DLY 2: 60

ENTRY DLY 1: 30

CLS CHK NO

CLS CODE NO

AREA A / P H / A

MODE: ALL/ PERIM

SYSTEM OPTIONS

CRS ZONE TM: 0

PWR FAIL HRS: 1

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 37 38

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XR20 Guide d'installation Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XR20