Digital Monitoring Products XR20 Guide d'installation télécharger pdf (Page 16)

Digital Monitoring Products XRSuper6/XR20/XR40 Programming Guide

CommuniCaTion

3.3

ACCNT NO: 12345

Account Number

Enter the account num ber sent to the receiver.

DD, NET - The range of account numbers for Digital Dialer and Network is 1 to

65535. For account numbers of four digits or less, you do not have to enter leading

zeros. The panel automatically right justies the account number.

4-2, M2E, and CID - The account number range for these formats is 1 - 9999.

3.4

XMIT DELAY: 30

Transmit Delay

Enter the number of seconds (15 to 45 seconds) the panel waits before sending

burglary alarm reports to the receiver. The bell and relay outputs are not delayed

during this period. Program Burglary Outputs for steady, and set Abort Reports to

YES if Opening and Closing reports are not being sent. Enter 0 (zero) to disable this

function. The default is 30.

If the area where the alarm occurred is disarmed during the Transmit Delay time,

only an Abort Report (S45) message is sent to the receiver. If the area where the

alarm occurred is disarmed after the alarm message is sent to the receiver but

before the Bell Cutoff time expires, even if the alarm was silenced, an Alarm

Cancelled (S49) message is sent. The Alarm Cancelled report cannot be disabled.

Note: For UL Installations, the combined Transmit Delay (Abort Window) and

Entry Delay must not exceed one (1) minute.

3.5

DTMF NO YES

DTMF

YES enables tone dialing. NO enables rotary dialing.

3.6

DFR TEST NO YES

Defer Test Time

Select YES to allow the programmed test report to be deferred if the panel

communicates with a receiver within the time set in Test Frequency. Select NO to

send the test report as programmed in Test Frequency regardless of previous panel

communication.

3.7

EVENT MGR: SND

Event Manager

This option species when non-alarm reports are sent to the receiver. This selection

does not affect zone alarm, zone trouble, zone restoral, supervisory, or serviceman

messages. Closing reports are not delayed if you have programmed a YES for the

Bell Test option.

SND DLY KEEP

SND - All reports are sent to the receiver as they occur.

DLY - All non-alarm reports are held until the panel memory buffer contains 40

events on the XRSuper6, 66 events on the XR20, and 100 events on the XR40, or

until the panel’s next communication with the receiver.

Note: If BELL TEST is YES, Closing reports are not delayed.

Note: NET communication does not delay any messages.

KEEP - All non-alarm reports are held in the panel memory buffer until they are

overwritten by new activity. You can view the contents of the buffer using the DMP

Remote Link™ software, or the Display Events function in the User Menu. Contact

ID, Modem IIe, and 4-2 formats do not delay reports but send them as they occur.

Time update from the SCS-1R Receiver: The XRSuper6/XR20/XR40 requests a time

update each time (once each day maximum) the panel contacts the receiver. The

Update Time to Panel option must be set to YES. In addition, the central station

automation system must be congured to update the time in the receiver at least

once each day.

3.8

TEST FREQ: 0

Test Frequency

Allows you to set how often the panel test report is sent to the receiver. Enter from

1 to 60 days. Enter zero to disable the test report.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XR20 Guide d'installation Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XR20