Digital Monitoring Products XR550 Manuel d'instructions télécharger pdf (Page 28)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

DEVICE SETUP

The 734/734N/734N-WiFi module provides a bypass-only option for REX on Zone 3. When

Zone 3 opens from a normal state, only a bypass occurs: the on-board relay does not

activate. This bypass-only option uses two methods of REX. The rst REX device provides

the programmed Bypass entry/exit timer. The second REX device, or manual device such as

a door knob, unlocks the door.

An example of the bypass-only conguration is a door to an ofce that is locked 24 hours a

day. Users pass a REX motion detector positioned by the door to begin the programmed exit

timer. Within the programmed number of seconds the user must then manually activate a

second device, such as a REX device or manual door knob, to unlock the door.

If the door is opened after the programmed number of seconds, the zone goes into alarm.

6.19.5 Zone 3 REX Strike Time

Enter the number of REX seconds to elapse. Range is from 5 to 250 seconds. Press any top

row select key to enter the number of seconds. The default is 5 seconds.

6.19.6 Activate Onboard Speaker

Select YES to enable the onboard piezo speaker for local annunciation. Select NO to turn

the piezo off for all operations. This does not affect remote annunciator open collector

(RA) operation. The default is NO.

6.19.7 Card Options

Press any top row Select key to display options. Press the select key under DMP, CUSTOM, or

ANY to select that option. Select DMP to indicate the reader sends a 26-bit DMP data string.

Press the COMMAND key to display REQUIRE SITE CODE.

Note: When set to DMP, the 734/734N/734N-WiFi converts 17 bits of the 26-bit data string

into a 5-digit number.

Select CUSTOM if using a non-DMP card or user code length of 6 to 12 digits.

Default is DMP.

Select ANY to allow all card reads to activate the door strike relay. The door strike relay

is activated for the length of time programmed in ZN 3 REX STRIKE TIME. No user code

information is sent to the panel.

6.19.8 CustomCardDenitions

Wiegand Code Length

When using a custom credential, enter the total number of bits to be received in Wiegand

code including parity bits.

Press any top row Select key to enter a number between 1-255 to equal the number of bits.

Default is 26 bits.

Typically, an access card contains data bits for a site code, a user code, and start/stop/

parity bits. The starting position location and code length must be determined and

programmed into the 734/734N/734N-WiFi Module.

01110101101101010001100111

First Bit

Received

Position = 0

Site Code

Position = 1

Length = 8

User Code

Position = 9

Length = 16

Last Bit

Received

Position = 25

In this example the Wiegand Code Length = 26 bits.

6.19.9 734 Site Code Programming

Site Code Position

Enter the site code start position in the data string. Press any top row Select key to enter a

number between 0-255. Default is 1.

6.19.10 Site Code Length

Enter the number of characters the site code contains. Press any top row Select key to

enter a number between 1-16. Default is 8.

6.19.11 User Code Position

Dene the User Code start bit position. Press any top row Select key to enter a number

between 0-255. Default is 9.

ZN 3 REX STRIKE

TIME: 5

ACTIVATE ONBOARD

SPEAKER? NO YES

CARD OPTIONS:

DMP

CARD OPTIONS:

DMP CUSTOM ANY

WIEGAND CODE

LENGTH: 26

SITE CODE

POSITION: 1

SITE CODE

LENGTH: 8

USER CODE

POSITION: 9

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 77 78

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XR550 Manuel d'instructions Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XR550