Digital Monitoring Products XR550 Manuel d'instructions télécharger pdf (Page 70)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

APPENDIX

Failed Zones Display

For each zone that did not trip (failed), except key fobs, at least once during the Walk

Test, all keypads with matching Display Areas programming display the zone name and

number and buzz for one second. Any selected (*FI *PN *SV) 24-hour zone that is faulted

at the end of the Walk Test displays a trouble condition for that zone regardless of the

message programmed for the open or short condition of the zone and a zone trouble is sent

to the receiver. Press the COMMAND key to display the next failed zone.

Note: For the Wireless Check-in Test, failed wireless zones display only on the keypad.

Zone Verify/Fail reports are not sent to the central station receiver for the wireless check-

in test.

22.5 Keypad Speaker Operation

When using LCD Keypads, the panel provides distinct speaker tones from the keypad for Fire, Burglary, Zone

Monitor, and Prewarn events. The list below details the conditions under which the speaker is turned on and off for

each event.

Fire On - Fire zone alarm and Bell Output or Fire Bell Output is ON.

Off - Alarm Silence.

Burglary On - Burglary zone alarm and Bell Output or Burglary Bell Output is ON.

Off - Alarm Silence.

Zone Monitor On - One time only when a monitored zone is tripped.

Off - After one tone.

Prewarn On - During Entry Delay.

Off - When Entry Delay expires.

22.6 Cross Zoning

Caution must be taken when cross zoning devices to ensure that the Cross Zone Time is long enough to allow an

intruder to trip both devices before it expires. A Cross Zone Time that is too short may allow an intruder to trip the

devices and allow only a zone fault report be sent to the central station.

When a Cross Zoned zone trips a FAULT report is sent to the SCS-1R or SCS-VR Receiver. When two Cross Zoned

zones trip within the Cross Zone Time, both zones send ALARM signals to the receiver. For example, if zones 1 and

2 are Cross Zoned zones, and only zone 1 trips, a FAULT report is sent to the receiver for zone 1. If zone 1 trips and

zone 2 trips within the Cross Zone Time, an ALARM report is sent to the receiver for zone 1 and zone 2.

22.7 Events Manager

The Events Manager allows you to delay sending certain reports to the central station receiver. Reports can be

kept in the panel memory until overwritten by new activity or held until the memory buffer reaches 50 events

or 50 door access granted events. When the buffer is full, the panel automatically sends the stored reports to

the central station receiver. The table lists the panel reports you can delay using the Events Manager option.

See Figure 10.

22.8 UserProles

A prole denes the authority of each user code in the system. Proles are programmed in the Keypad User Menu. Several

characteristics associated with each User Prole dene its authority within the system. To effectively program an XR150/

XR350/XR550 Series system, you must understand the interrelationship between proles, devices, output groups, and

areas. Below is a brief explanation of the User Prole elements. For more information about user proles, refer to the

User Proles Record and the XR150/XR350/XR550 User’s Guide (LT-1278).

Note: Proles cannot be changed via keypad in an All/Perimeter or Home/Sleep/Away system. Use the default proles 1

through 10.

Prole Number - Each prole may be assigned a unique number from 1 to 99.

Prole Name - Each prole may be assigned a 32-character name. The Prole Number is the default name.

Area Number - Each prole may be assigned specic areas of the system for arming and disarming. When creating proles

1 to 98, NO areas are assigned by default. The default for prole 99 is ALL areas assigned. Prole 99 is preprogrammed in

the system at the factory.

Access Area Number - Each prole may be assigned door access area assignments. Default for prole 1 to 98 is NO areas

assigned. Default for prole 99 is ALL areas assigned. Prole 99 is preprogrammed at the factory.

Output Group Assignment - Each prole may be assigned an output group number from 1 to 10. Default for prole 1 to

98 is NO output group assigned. Default for prole 99 is output group 10. Your system may by programmed to turn on an

output group at certain keypads when door access occurs.

User Menu Assignments - Each user prole may have any of the menus assigned to it as shown in the following User

Prole Record. The User Prole Record lists the user menu prole assignments and the system functions users are allowed

to access based on the prole numbers assigned to their codes.

SOUTH LOBBY

ZONE: 10 -FAIL

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 76 77 78

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XR550 Manuel d'instructions Page 70

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XR550