Digital Monitoring Products XR550 Manuel d'instructions télécharger pdf (Page 60)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

ZONE INFORMATION

18.12 Alarm Action

This option allows you to change any Zone Type standard denitions. When the Zone

Type is specied, the Alarm Action for that zone is stored in memory.

If the Zone Type is Blank, Night, Day, Exit, Auxiliary 1, or Auxiliary 2 it is a non-24-hour

zone and the Alarm Action programing begins with Disarmed Open.

If the Zone Type is Fire, Panic, Emergency, or Supervisory it is a 24-hour zone that is

always armed and the Alarm Action programming begins with Armed Open.

The Fire Verify Zone Type functions the same as Fire Type, with the following

exceptions: When a Fire Verify zone initiates an alarm, the panel performs a Sensor

Reset. If any Fire Verify zone initiates an alarm within 120 seconds after the reset, an

alarm is indicated. If an alarm is initiated after 120 seconds, the cycle is repeated and a

zone fault report is sent to the receiver.

Do NOT program Fire Verify Zone Types for Zone Retard.

18.13 Disarmed Open

Denes the action taken by the panel when the zone is opened while the area is

disarmed. There are three actions to dene: Report to transmit, Relay Output to

activate, and Relay Output action.

You must also make these selections for the Disarmed Short, Armed Open, and Armed

Short zone conditions. Press COMMAND to continue.

18.14 Report to Transmit

Press any Select key to display the following report options: A, T, L, S, C, and - (dash).

ALARM - Select A to send an alarm report to the receiver and activate the bell output

according to zone type. The zone name appears in the panel alarmed zones and status

lists.

TROUBLE - Select T to send a trouble report to the receiver. The zone name appears in

the panel alarmed zones and status lists.

Note: UL requirements prevent the Alarm (A) and Trouble (T) action for Fire (FI), and

Fire Verify (FV) zone types from being changed.

LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell output

activates and the zone name appears in the panel alarmed zones and status lists.

- (Dash) - When you select a – (dash), reports are NOT sent to the receiver. The bell

output does not activate and there is no display in the panel alarmed zones or status

list. Only the relay output selected in the next section operates.

DOOR PROPPED - Selecting D allows the following operation: The time programmed into

ENTRY DLY 4 in the System Option section begins to count without displaying on keypad.

If the time expires and the zone has not returned to normal, the keypad trouble buzzer

starts and CLOSE THE DOOR appears on the keypads programmed into the PREWARN

ADDRESS section. The time programmed into ENTRY DLY 4 begins to count down again

internally. If the time expires a second time and the zone has not returned to normal, a

fault report is sent to the receiver and the zone name - OPEN message displays on the

keypads until a code is entered. The bell output does not activate for the Door Propped

operation.

SILENCE/RESET - Select S when the zone (not FI, SV, or FV) is connected to a DMP Model

303 Silence/Reset switch, the zone can be used to silence the alarm bell and perform a

sensor reset without using a keypad. A report is NOT sent to the receiver except for the

bell silence report.

CANCEL AMBUSH - Select C for the zone to cancel the Early Morning Ambush timer and

stop an Ambush message from being sent to the receiver. Faulting the zone takes the

place of a second user code being entered at the keypad and is only available for non-

re type zones. Area assignment for the zone does not affect this option. See Early

Morning Ambush in Area Information programming .

18.15 Output Number

You can specify any of the Relay Outputs on the panel to be activated by a zone

condition (1 to 6, 500 to 999 if Model 716 used, D1 to D16, G1 to G20). The output

can be activated regardless of the report to transmit or whether or not the zone is

programmed as local. An output activated by an armed zone is turned off when the zone

area is disarmed by a user.

To enter an output number, press a top row Select key followed by the output number.

Press the COMMAND key.

18.16 Output Action

Entering an Output Number displays this option. This option allows you to assign an

output action to the relay: Steady, Pulse, Momentary, or Follow.

Note: Some wireless devices whether powered using an AC adaptor or a battery, ignore

some output action programming.

ALARM ACTION . . . .

DISARMED OPEN

MSG: TROUBLE

A T L -

D S C

OUTPUT NO: 0

OUTPUT: NONE

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 77 78

Commentaires sur ces manuels

Pas de commentaire

Digital Monitoring Products XR550 Manuel d'instructions Page 60

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Digital Monitoring Products XR550